AR9 / PCC

Replacement Firing Pin Spring for JP 9mm Bolt (JPBC-9MMA) This firing pin spring is compatible only with the JP 9mm Bolt and firing pin and should not be used with any other bolt assembly.

Molded polymer cover fits in the underside of a disassembled AR-15 .22 conversion upper receiver to prevent the bolt from falling out and keep dirt and debris out of internal components. Can be installed on any standard...

Buffer Pad ONLY

Glock Factory 9mm Magazine Follower

Rifle Spacer ONLY

High-density synthetic rubber wedge drops into the space behind the takedown pin in the lower receiver to provide tension between the receiver halves and prevent movement for improved accuracy...

Low-friction Delrin disk fits on the end of the buffer spring, opposite the buffer, and stops the annoying "twang" of the buffer hitting the rear of the receiver extension during recoil.

  TTI Magazine Spring for Glock 140mm Magazines w/Large +5/+6 Base pad  Designed exclusively to work with the TTI base pads. Each coil compresses and stacks into the neighboring coil to provide the highest...

This easy to install, inexpensive, drop in upgrade is perfect for any AR rifle.  CNC machined from a solid piece of 6061-T6 aluminum, the Billet Mag Release Button is larger and easier to manipulate than the Mil-Spec...

Highest quality available. For use with DP basepads. Extra length can be trimmed for shorter mags.

Glock Factory Mag Spring for use in extended 19-23 round magazines

Complete shim kit allows you to properly index your muzzle device to your barrel. The kit comes with seven different thicknesses of stainless steel shims. The shims can be used alone or in different combinations to give...

Magpul Original Equipment Stock Tigger Guard

Pistol caliber carbines such as 9mm, .40 S&W, .45 ACP, and 10mm are a blast to shoot but can be tough on AR-15's internal components. Without a properly tuned blowback system, you run the risk of being overly destructive...

Mil-Spec Barrel Nut

  Quick detach sling swivel for mounting to Nordic Components mounting plates or other QD mounts. Release button flush to top of swivel body to minimize unintentional release Pull-tested to over 300...

Glock Factory Mag Spring for use in extended 31-33 round magazines

Wolff Mag Spring for use in TF 41+1 Glock Mag Extension Kit

Wolff Mag Spring for use in TF +10 Colt Mag Extension Kit

23 or 36 coil option 17-2 stainless steel Extra power for the 33 round Glock Magazine Extra power for +10 extensions Will also work on CZ Scorpion...

ALWAYS HAVE A SPARE •EASY TO REPLACE Basepad Service Kit For all Dawson Precision Basepads   5 Pack Basepad Springs, 5 Pack Basepad Detents

JP Enterprises trigger spring kit will give your stock AR-15 a 4 to 4-1/2 lb trigger pull; with JP trigger parts the same springs will produce a 3 to 3-1/2 lb trigger pull. This trigger spring kit will significantly improve...

Field stripping your AR15 will never be easier when using these extended take down pins. No more looking around for a tool, or using the nose of a round. Simply grab the extended head and pull the takedown pin out. The...

We take a mil spec extractor, and polish the leading surface so that you are assured smooth function. We’ve found that this single operation is an important process to help with feeding the round into the chamber while...

The AP Mag ID Kit for pistol includes 6 base pad ID’s, numbered 1 through 6, that are laser cut from premium grip tape to fit the most popular magazines and base pads. The Pistol ID’s come in either red, blue,...

Replacement Firing Pin for JP 9mm Bolt (JPBC-9MMA) This firing pin is compatible only with the JP 9mm Bolt and should not be used with any other bolt assembly.

An extra firing pin is a perfect addition for your range bag. If you are a recreational shooter, or a competitor in USPSA PCC Class shoots don't let your range day or competition end early. We rarely have firing pins break...

What no one has done before is address the force of the bolt and buffer slamming into the barrel on the return stroke. Now, we have! The stainless cushion will now actually soften that impact...

This firing pin is hands down, going to be your best chance as a “non-breakable” firing pin. We chose to use 17-4 stainless steel because it’s stronger and tougher than s7 tools steel; which is the common...

Push-button quick-detach sling swivel for 1-1/4" webbing, compatible with QD sling attachment points. Manganese-phosphate finished steel. Combine with MS1 Sling for dedicated two-point sling, or with MS1 MS4 Adapter for...

This spacer allows a Carbine or 9mm buffer or Silent Captured Spring to fit and function in a rifle-length buffer tube.

Tool steel Hammer and Trigger Pins work to remove the slop between the trigger, hammer and the receiver. Pins feature Allen heads for easy tightening and are finished in black oxide. Trigger and hammer may have to be reamed...

Production Division Legal   Glock 9/40 extended base pads are CNC machined from aluminum and hard anodized. This lengthens the magazine .25" to make for easier, more reliable magazine changes. They also allow you to...

Repair your Carbine with this Bolt Catch Replacement Kit   Kit contains: Bolt...

Please do not attempt to purchase large capacity magazines if you reside in a location where you may not legally posses them (Ca, Co, Ct, DC, Hi, Il, Md, Ma, NJ, NY, OH) please check laws for your state. Mag ...

Nordic Components, The M-LOK QD Sling Mount Provides a Forward Attachment Point For a Push-Button QD Sling, Machined From Milspec Anodized Aluminum, The Low-Profile M-LOK QD Sling Mount Features Beveled Edges to Reduce...

Similar in concept to the MOE-K, the MOE-K2 is a drop in upgrade for AR15/M4's that offers a more vertical grip angle, but in a full-size grip design. The steeper vertical grip angle is optimized for use on PDW (Personal...

This QDA Plate allows for the quick detach/attachment of the popular push button style sling swivels.This will attach to any of our NC1 Style, 2″ diameter Hand Guards. Comes with one #10-32 x 1/2″Flat Head...

The Seekins Precision Enhanced Bolt Catch is an easy to install upgrade that improves the functionality of any MIL SPEC lower receiver.  Designed to make bolt manipulation easier, the unique, oversized bolt catch has an...

Our QD sling mounts accepts quick detach sling swivels.  The design incorporates a mounting system that was designed in house and used on all of our KeyMod features.  You won't see the big screw heads with any of...

When we came out with the TACCOM recoil system, we developed the shortest stroking system you could buy that still allowed for the Bolt Hold Open to function, we were all amazed at just how smooth this system was. But you...

Full Length A2 Rifle Buffer Tube for use with Fixed Rifle Length Stock

The Seekins Precision Billet Trigger Guard is a functional upgrade for any mil-spec lower receiver.  Machined from a solid piece of 6061-T6, the profile and size accommodate winter gloves while maintaining precise...

Shooters wanted an ODIN Works XMR (eXtended Magazine Release) that worked with Magpul BAD levers. Machined from billet 6061 aluminum featuring the ODIN boomerang cuts, the XMR 2 is the one accessory every AR with or without...

Fortis QD End Plate features the quick detach swivel socket.  This AR15 lower receiver end plate is designed for carbine style buffer tubes for the AR15 & 308 platforms. Features: Fully radiused edges, inside...

Hand-filling, ergonomic profile with finger grooves, and many other features improves shooting comfort and accuracy. Suregrip adds an overmolded, rubberized covering to the polymer body for a superior grip and added cushion...

We designed our rail pieces with a self contained assembly that has no visible signs of the screw head.  Available in three different lengths. Features: Material: Aircraft Grade 6061-T6 Aluminum Finish: Military...